ASTM A213M-09材料比较表（ASTM→KS，，吉斯, DIN, BS, NBN, NF, UNI)

表1-1：

年级	UNS Designation	C	Mn	P	S	si	Nickel	铬	钼
T2	K11547	0.10–0.20	0.30–0.61	0.025	0.025b	0.10–0.30	...	0.50–0.81	0.44–0.65
T5	K41545	0.15	0.30–0.60	0.025	0.025	0.5	...	4.00–6.00	0.45–0.65
T5b	K51545	0.15	0.30–0.60	0.025	0.025	1.00–2.00	...	4.00–6.00	0.45–0.65
T5c	K41245	0.12	0.30–0.60	0.025	0.025	0.5	...	4.00–6.00	0.45–0.65
T9	K90941	0.15	0.30–0.60	0.025	0.025	0.25–1.00	...	8.00–10.00	0.90–1.10
T11	K11597	0.05–0.15	0.30–0.60	0.025	0.025	0.50–1.00	...	1.00–1.50	0.44–0.65
T12	K11562	0.05–0.15	0.30–0.61	0.025	0.025b	0.5	...	0.80–1.25	0.44–0.65
T17	K12047	0.15–0.25	0.30–0.61	0.025	0.025	0.15–0.35	...	0.80–1.25	...
T21	K31545	0.05–0.15	0.30–0.60	0.025	0.025	0.50–1.00	...	2.65–3.35	0.80–1.06
T22	K21590	0.05–0.15	0.30–0.60	0.025	0.025	0.5	...	1.90–2.60	0.87–1.13
T23	K40712	0.04–0.10	0.10 - -0.60	0.03	0.01	0.5	0.4	1.90–2.60	0.05–0.30
T24	K30736	0.05–0.10	0.30–0.70	0.02	0.01	0.15–0.45	...	2.20–2.60	0.90–1.10
T36	K21001	0.10–0.17	0.80–1.20	0.03	0.025	0.25–0.50	1.00–1.30	0.3	0.25–0.50
T91	K90901	0.07–0.14	0.30–0.60	0.02	0.01	0.20–0.50	0.4	8.0–9.5	0.85–1.05
T92	K92460	0.07–0.13	0.30–0.60	0.02	0.01	0.5	0.4	8.5–9.5	0.30–0.60
T122	K91271	0.07–0.14	0.7	0.02	0.01	0.5	0.5	10.0–11.5	0.25–0.60
T911	K91061	0.09–0.13	0.30–0.60	0.02	0.01	0.10–0.50	0.4	8.5–9.5	0.90–1.10

表1-2：

年级	UNS Designation	v dium	Boron	铌	Nitrogen	Aluminum	Tungsten
T2	K11547	...	...	...	...	...	...
T5	K41545	...	...	...	...	...	...
T5b	K51545	...	...	...	...	...	...
T5c	K41245	...	...	...	...	...	...
T9	K90941	...	...	...	...	...	...
T11	K11597	...	...	...	...	...	...
T12	K11562	...	...	...	...	...	...
T17	K12047	0.15	...	...	...	...	...
T21	K31545	...	...	...	...	...	...
T22	K21590	...	...	...	...	...	...
T23	K40712	0.20–0.30	0.0010–0.006	0.02–0.08	0.015	0.03	1.45–1.75
T24	K30736	0.20–0.30	0.0015 - -0.007	...	0.012	0.02	...
T36	K21001	0.02	...	0.015–0.045	0.02	0.05	...
T91	K90901	0.18–0.25	...	0.06–0.10	0.030–0.07	0.02	...
T92	K92460	0.15–0.25	0.001–0.006	0.04–0.09	0.030–0.07	0.02	1.5–2.00
T122	K91271	0.15–0.30	0.0005–0.005	0.04–0.10	0.040–	0.02	1.50–2.50
T911	K91061	0.18–0.25	0.0003–0.006	0.06–0.10	0.040–0.09	0.02	0.90–1.10

Note:

A Maximum, unless range or minimum is indicated. Where ellipses (...) appear in this table, there is no requirement, and analysis for the element need not be determined or reported.

B可以订购T2和T12，硫含量最大为0.045。参见16.3。

c或者，代替该比率最小，该材料的最小硬度应在硬化条件下的最小硬度为275 hv，定义为在奥氏体化和冷却到室温后，但在回火之前定义。
硬度测试频率应为每个热处理量的两个产品样本，并且应在材料测试报告中报告硬度测试结果。

表2-1：

ASTM 标准	UNS NO.	KOREA/JAPANES			GERMAN
ASTM 标准	UNS NO.	KS/JIS符号	KS/jis numbe	Remarks	DIN Type	DIN Number	产妇 Number	Remarks
312 Seamless and WeldedAustenitic防锈的Steel Pipe
TP 304	S30400	STS 304TP / SUS 304 TP	D3576 / G3459	(16)	X5CrNi 18 9	17440	1.4301	(3b)
TP 304H	S30409	STS 304HTP / SUS 304HTP	D3576 / G3459	(16)				(3)
TP 304L	S30403	STS 304LTP/SU	D3576 / G3459	(16)	X2 CrNi 19 9	17440	1.4306	(3b)
TP 310	S31000	304LTP	D3576 / G3459	(16)				(3)
TP 316	S31600	STS 310STP/SU	D3576 / G3459	(16)	X5 CrNiMo 18 10	17440	1.4401	(3b)
TP 316H	S34609	310STP	D3576 / G3459	(16)				(3)
TP 316L	S31603	STS 316TP / SUS 316TP	D3576 / G3459	(16)	X2 Crnimo 18 10	17440	1.4404	(3b)
TP 321	S32100	STS 316HTP /SU	D3576 / G3459	(16)	x10 CrNiTi 18 9	17440	1.4541	(3b)
TP 347	S34700	316HTP	D3576 / G3459	(16)	x5 crninb 18 9		1.4543	(3b)
TP 347H	S34709	STS 316LTP /SU	D3576 / G3459	(16)				(3)
		321LTP
		STS 321TP / SUS 321TP
		STS 347TP / SUS 347TP
		STS 347HTP / SUS 347HTP

表2-2：

ASTM 标准	UNS NO.	英国			FRENCH			意大利人
ASTM 标准	UNS NO.	B.S Number	B.S等级	Remarks	afnor类型	NF Number	拉马克斯	UNI类型	UNI Number	拉马克斯
312无缝和焊接的奥氏体不锈钢管
TP 304	S30400	3605	304S18		TU Z6 CN19-10	49-230		X5 CRNI 18 10	6904	(3b)
TP 304H	S30409	3605	304S59		TU Z6 CN19-10	49-214		X8 CRNI 19 10	6904	(3b)
TP 304L	S30403	3605	304S14		TU Z2 CN19-11	49-230		X2 CrNi 18 11	6904	(3b)
TP 310	S31000							x22 cr ni 25 20	6904	(3b)(11)
TP 316	S31600	3605	316S18		Z 6 CND 17.11	35-573	(3b)	X5 CrNiMo 17 12	6904	(3b)
TP 316H	S34609	3605	316S59		tuz6cnd17-12	49-230		x8 crninb 17 12	6904	(3b)
TP 316L	S31603	3605	316S14		TUNZ2CND17-12	49-230		X2 Crnimo 17 12	6904	Dalmine 941(3b)
TP 321	S32100	3605	321S18		Z6 CNT 18.11	49-230		X6 CrNiTi 18 11	6904	(3b)
TP 347	S34700	3605	347S18		Z6 CNNb 18.11	35-573	(3b)	X6 CrNiNb 18 11	6904	(3b)
TP 347H	S34709							X6 CrNiNb 18 11	6904	(3b)

ASTM A213标准范围：

1.1 This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T91, TP304, etc. These steels are listed in Tables 1 and 2.
1.2包含字母H的等级为H中，其指定要求与不包含字母的类似成绩的要求不同。这些不同的要求提供的蠕变强度比在没有这些不同要求的类似等级中可以达到的更高的蠕变强度。
1.3 The tubing sizes and thicknesses usually furnished to this specification are 1/8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification.
1.4 SI单元或英寸磅单元中所述的值应分别视为标准。在文本中，SI单元在括号中显示。每个系统中所述的值可能不是确切的等效物。因此，每个系统应独立使用另一个系统。结合两个系统的值可能会导致标准不合格。除非在订单中指定此规范的“ M”名称，否则应适用英寸磅的单元。
TABLE 1 Chemical Composition Limits, %A, for Low Alloy SteelA Maximum, unless range or minimum is indicated. Where ellipses (…) appear in this table, there is no requirement, and analysis for the element need not be determined or reported.

B可以订购T2和T12，硫含量最大为0.045。参见16.3。

c或者，代替该比率最小，该材料的最小硬度应在硬化条件下的最小硬度为275 hv，定义为在奥氏体化和冷却到室温后，但在回火之前定义。硬度测试应在产品的中间厚度进行。硬度测试频率应为每个热处理量的两个产品样本，并且应在材料测试报告中报告硬度测试结果。